Skip to content
Back to Learn

DMA setup step by step: what plugs in where, in order

Set up your DMA card, second PC, MAKCU or FERRUM and video fuser in the right order. Every cable, which port it goes in and the guide for each step.
GuidePublished · developer · 25 reads

Set everything up in this order: your report, your BIOS, your card, your second PC, your DNA ID, the flash, your software, your aim device, then your fuser.

Warning. Never boot into Windows on your main PC with a card that isn't flashed with our firmware yet. Keep your main PC in the BIOS while you get your DNA ID and flash. If you already did, reinstall Windows on your main PC before you launch any game.

Every cable at a glance

PartPlugs intoWith
Your DMA cardA free PCIe slot in your main PCNothing, it takes power from the slot
Your card's JTAG port, closest to the gold stripA rear USB 3 port on your second PCThe cable from the box, only while you get your DNA ID and flash
Your card's data port, furthest from the gold stripA rear USB 3 port on your second PCThe same cable, every day after the flash
Your mouseMAKCU's right port, or FERRUM's middle portIts own cable or receiver
MAKCU's left port, or FERRUM's left portA rear USB port on your main PCA cable from the box
MAKCU's middle port, or FERRUM's right portA USB port on your second PCA cable from the box
Your main PC's graphics cardYour fuser's main input, PC1 (M)HDMI or DisplayPort, depending on your fuser
Your second PC's video outYour fuser's second input, PC2 (S)HDMI or DisplayPort, depending on your fuser
Your fuser's outputYour monitorHDMI or DisplayPort, depending on your fuser

The GODLIKE 100T's bracket seen from outside the PC: DATA port first, then the JTAG port, then the kill switch nearest the gold strip end

1. Before your card goes in

2. Put your card in your main PC

Shut down and unplug your main PC, then put your card in a free PCIe slot. The short x1 slot works, since your card only uses one lane. Make sure the kill switch on the bracket is on, then start your main PC and go into the BIOS. How to install a DMA card

3. Get your second PC ready

Plug the cable from the box into your card's JTAG port and into a rear USB 3 port on your second PC. Install MewTools on your second PC and install the JTAG driver from its Drivers screen. Second PC setup

4. Send your DNA ID

Get your card's DNA ID with MewTools and send it with your msinfo32 report from your order page. It usually takes us about 2 to 24 hours at most to build your firmware, and we will email you when it's done. Your DNA ID

5. Flash your firmware

Flash the .bin file with MewTools while your main PC is in the BIOS, then move the cable to your card's data port, restart your main PC into Windows, run the activator and run the speed test. Flashing your firmware and Mew Activator

6. Install your software

Your software goes on your second PC only. Which software to get

7. Your aim device, if you have one

Your mouse plugs into the aim device, one cable goes to your main PC and one to your second PC. The driver goes on your second PC. MAKCU setup or FERRUM setup

8. Your fuser, if you have one

Your fuser goes in last, with your main PC in the main input, your second PC in the second input and the output to your monitor. Set both PCs to the same resolution and make your second PC's background black. Video fuser setup

Every time you play

  1. Start your main PC, then your second PC.
  2. Run the activator on your second PC.
  3. Open your software.

If a step doesn't work

Common questions

  • What do I set up first, my DMA card or my second PC?
    Your card. Do your msinfo32 report and turn off Fast Boot, put your card in, then set up your second PC.
  • Which port on my DMA card does the cable go in?
    JTAG, the one closest to the gold strip, while you get your DNA ID and flash. Data, the one furthest from it, every day after that.
  • Do my two PCs have to be next to each other?
    Yes, close enough for the cable from your card's box to reach, because hubs and long extension cables cause dropouts.
  • Does anything get installed on my main PC?
    No. MewTools, the activator, your software and the aim device driver all go on your second PC.
Are we missing something?

Tell us what you came looking for and couldn't find, or what we got wrong, and we'll look into it. No account needed.

Did this help?

You don't need an account, this tells us what to write more of.