If your DMA software won't open, won't log in or can't reach your card, run the MewTools speed test first. If it passes, your card and firmware are fine. Work through the checks below on your second PC: the cause is usually a missing runtime, a wrong clock, the cable in the wrong port or the activator. If it fails, start with DMA card not working instead. If you got an error message, find its exact text in DMA error messages.
It won't open at all
- Missing runtimes.
Blurred's setup guide asks for Microsoft's Visual C++ Redistributable (x64) and the WebView2 Runtime. Get both from Microsoft's site (WebView2 already comes with Windows 11) and restart after you install them. A "VCRUNTIME140.dll was not found" error means the Visual C++ one is missing, and its own page has the steps. For Streck, ask in a ticket what it needs installed. - Windows Security took it.
Open Windows Security, then Virus & threat protection, then Protection history. If the loader is listed, it was quarantined, so ask your software's support what to allow. Don't turn Windows Security off completely. - Blocked before it starts.
SmartScreen and Smart App Control stop some programs from opening, the same way as in MewTools blocked by Windows. - The right PC.
The software only goes on your second PC.
It won't log in or activate
- The clock is wrong.
Blurred's loader checks your clock when it connects, and if it's off by more than a minute or the time zone is wrong, it can fail to log you in. Right-click the clock on the taskbar, choose Adjust date and time, turn on Set time automatically and Set time zone automatically, then press Sync now. - The license.
A software license is locked to your second PC. If you changed your second PC, the software's maker does the reset, not us.
It can't reach the card
Blurred shows this as "Failed to connect to memory acquisition device".
- The cable is on JTAG.
Move it to your card's data port, since JTAG is only for flashing. - The data driver.
In MewTools open Drivers and press Install next to Card data cable. If it says Ready, press Uninstall, then Install. Then check Device Manager shows FTDI FT601 USB 3.0 Bridge Device under Universal Serial Bus controllers with no warning triangle, and restart your second PC. - Only one program at a time.
Close MewTools and any other DMA tool before you start your software. - Cold boot both PCs.
A card stuck after a restart or sleep can't be reached. The steps are in Cold boot both PCs first.
The activator
Run the activator on your second PC every time your main PC restarts, before you open your software. If you skip it your card can't read memory, and your software often prints TINY PCIe TLP algorithm auto-selected. Your key is lifetime, so it never runs out (Your activation key).
If it hangs on activate device or won't activate, check your cable is on the data port and nothing else (MewTools or your software) has your card open, then cold boot both PCs and try again. The activator was updated in late October and older copies stop working, so if yours is from before that, download it again from your order page.
It connects but ESP doesn't show
- "Unable to locate valid DTB" or "Failed to find base address".
Cold boot first, and if it stays, you may need a memory map. - A game update.
Software is made per game, and after a big patch it can stop working until its maker updates it, so check their Discord. - Slow or laggy ESP.
That's a speed problem, so go to Low DMA speed.
Who to ask
For software help, start with Blurred in their Discord, Streck in Streck's Discord, or whoever you bought it from. We handle support for your card, firmware, flash and activator. Open a ticket in our Discord with a screenshot of the error and of the MewTools speed test, and we'll help you work out which side it is.
Common questions
- Why won't Blurred log in?
Blurred's loader checks your clock, and it can fail if the time is off by more than a minute or the time zone is wrong. Turn on Set time automatically and press Sync now. - Can MewTools and my DMA software run at the same time?
No. One program reaches your card at a time, so close MewTools before you start your software. - Who do I ask when my DMA software has a problem?
Your software's maker first, Blurred or Streck in their own Discord. We handle your card, firmware, flash and Mew Activator.
You don't need an account, this tells us what to write more of.
