Skip to content
Back to Learn

GODLIKE 100T DMA card: ports, lights and kill switch explained

What each port, light and switch on the GODLIKE 100T DMA card does, which cable goes where, and what the lights tell you when your card isn't working.
GuidePublished · developer · 29 reads

The GODLIKE 100T has two USB-C ports and a kill switch on its bracket, and four lights on the board. Data is the port you use every day, JTAG is the port you flash with, and the kill switch turns your card off.

The GODLIKE 100T: 1 data port, 2 JTAG port, 3 power switch, 4 data light, 5 PCIe status light, 6 power light, 7 ambient light, 8 PCIe connector

The two USB-C ports

The GODLIKE 100T's bracket seen from outside the PC: DATA port first, then the JTAG port, then the kill switch nearest the gold strip end

  • Data is the port furthest from the gold strip.
    Your software and the speed test use it, so your cable stays here after the flash.
  • JTAG is the port closest to the gold strip.
    You get your DNA ID and flash your firmware through it. It does nothing while you play.

The 100T comes with one cable, and it goes in a rear USB 3 port on your second PC with no hub. You can move it between JTAG and data with your main PC on.

The kill switch

The kill switch is on the bracket next to the two ports, so you reach it from the back of your PC with the case closed. With it off, your card's lights go out and your PC finds nothing in the slot when it starts, and your firmware stays on your card.

NEVER switch it while your PC is on. Shut your main PC down, switch it, then turn your PC on. When you switch your card back on, run the activator again. What the kill switch does

The lights

These come from GODLIKE's own notes for the 100T.

LightWhat it tells you
PowerOn: your card has power. Off: no power, so check the kill switch and how your card sits in the slot
PCIe statusOn: your card is properly connected to your motherboard. Blinking: the connection failed. Off: your card is faulty, or the firmware is missing or incompatible
Data transferOn while data moves to your second PC, like during a speed test, and off the rest of the time
AmbientOnly for looks

The gold strip and the slot

The gold strip goes into a PCIe slot on your main PC. Your card uses one lane, so it fits any free slot, the short x1 slot included. It takes its power from the slot, so no cable goes to your power supply. How to install a DMA card

Some slots share lanes with an M.2 socket and switch off when a drive is in it. Which slot to pick

What the lights tell you when it isn't working

  • No lights at all.
    Make sure the kill switch is on, then shut down, unplug your main PC, touch a bare metal part of the case and reseat your card until no gold shows above the slot. If there's still nothing, try another slot.
  • The PCIe status light blinks.
    Your card has power but its connection to the slot failed. Reseat it, try another slot, then step the slot's speed down in your BIOS.
  • Power light on, PCIe status light off.
    The firmware is missing or doesn't suit your card. Open a ticket with a photo of your card and a screenshot of Card Check in MewTools after you press Read card.
  • Your card is on a riser.
    Put it directly in a slot, because cheap or long risers make cards unstable.

Every other fix is in DMA card not working.

The chip

100T is the size of the main chip, a Xilinx Artix-7. A bigger chip has more room for firmware, and every firmware we make needs a 75T or a 100T. Why the 100T

Common questions

  • Which USB-C port on the GODLIKE 100T is JTAG?
    The one closest to the gold strip. Data is the one furthest from it.
  • Which port do I use to play?
    Data. JTAG is only for your DNA ID and flashing.
  • What does the switch on a DMA card do?
    It's the kill switch. With it off your PC finds no card in the slot, and you only switch it with your PC shut down.
  • Why are my DMA card's lights off?
    The kill switch is off, your card isn't fully in the slot, or the slot is switched off by a shared M.2 socket.
  • Does the 100T need a power cable?
    No. It takes its power from the PCIe slot.
Are we missing something?

Tell us what you came looking for and couldn't find, or what we got wrong, and we'll look into it. No account needed.

Did this help?

You don't need an account, this tells us what to write more of.