Skip to content
Back to Learn

MAKCU troubleshooting: no COM port, mouse not working, software won't connect

Fix a MAKCU with no COM port, a mouse that won't pass through, software that can't connect, the wrong baud rate or a USB sound that keeps looping.
GuidePublished · developer · 16 reads

If MAKCU isn't working, check the wiring first: your mouse in the right port (USB3), your main PC in the left port (USB1) and your second PC in the middle port (USB2). Then cold boot both PCs, because MAKCU takes its power from your main PC and a restart doesn't reset it.

Every driver and tool goes on your second PC, and the full setup is in MAKCU setup.

MAKCU's three ports: left to the main PC, middle to the second computer, right for the mouse

What's wrongGo to
Your mouse doesn't move on your main PCMouse not passing through
No COM port in Device ManagerNo COM port
Your software can't connect or doesn't move the mouseSoftware can't connect
It worked, then stopped after your main PC startedStops working after your main PC starts
The USB sound keeps loopingKeeps disconnecting

Mouse not passing through

Your mouse works through MAKCU with no software running, so if the pointer doesn't move, it's the wiring, the USB port or the mouse.

  • Check the ports.
    Your mouse goes in the right port and your main PC's cable in the left.
  • Use a port on the back of your main PC.
    Front and top ports go through a cable inside the case and cause dropouts.
  • Try another mouse.
    MAKCU limits how much power its mouse port gives, so a mouse or receiver that pulls a lot can drop out or lose its lighting.
  • Bluetooth doesn't go through MAKCU.
    A wireless mouse works with its own USB receiver in the right port.

No COM port

  • The CH343 driver isn't installed.
    In MewTools, open Drivers and press Install next to MAKCU. Or get it from WCH, the chip maker.
  • A cable is unplugged.
    MAKCU needs your main PC's cable for power, so check both.
  • Your second PC's cable is in the wrong port.
    It goes in the middle, USB2.
  • The USB port or the cable.
    Try another port on your second PC, then the other cable from the box.
  • Cold boot both PCs.

The port shows in Device Manager under Ports (COM & LPT) as USB-Enhanced-SERIAL CH343, with its number in brackets.

Device Manager with Ports (COM & LPT) open, showing USB-Enhanced-SERIAL CH343 (COM5). The number in brackets is MAKCU's COM port

Software can't connect

  • Wrong COM number.
    Check it against Device Manager. If your software needs a number below 10, see Fixing a COM port 10 or higher.
  • Wrong speed.
    MAKCU runs at 115200 or 4 Mbps, and your software has to use the same one. On v4 firmware, hold MAKCU's left button for about a second. On v3, press it four times within two seconds. The LED next to the left port flashes once for 115200 and four times for 4 Mbps. The speed setting in Device Manager does nothing.
  • Another program has the port.
    Only one program can use the port at a time. Close the MAKCU Toolkit, any makcu.com tab and MewTools before you start your software.
  • Logging is on.
    Turning on logging in MAKCU's own tool puts MAKCU on 4 Mbps, so software set to 115200 stops connecting. Turn logging off, or switch the speed with the left button.
  • Your software picked a different chip.
    Some mini PCs have a CH340 chip on the board, and it shows under Ports (COM & LPT) as USB-SERIAL CH340. MAKCU is the CH343 entry, so pick that port. If your software grabs the CH340 by itself, uninstall the CH340 device in Device Manager before you start it.
  • Your software doesn't support MAKCU.
    Ask your software provider.

Test it without your software. Switch MewTools to Pro, open Aim Devices and wait for Connected, then run Test mouse move. If the pointer moves on your main PC, MAKCU works and the problem is in your software's settings.

Stops working after your main PC starts

After your main PC is on, unplug the left cable from MAKCU, wait a few seconds and plug it back in.

Keeps disconnecting

If the USB connect sound keeps looping, try the other cable and another USB port first, then cold boot both PCs. MAKCU's maker says a loop happens when one side has no firmware or the wrong firmware on it. Ours ship flashed and tested, so open a ticket before you try Repair flash.

What the lights mean

A solid light means that side is connected and working, and off means nothing is connected on that side. A slow blink means a warning or a setting being changed, so give it a few seconds, and if it still blinks, unplug and replug all the cables.

A controller

A gamepad needs XIM MATRIX Manager installed and running, and test it on a cable before you go wireless.

Still stuck

Open a ticket in our Discord and tell us which port each cable is in, what Device Manager shows and which software you use.

Common questions

  • Why does my MAKCU have no COM port?
    The CH343 driver isn't on your second PC, a cable is unplugged, or your second PC's cable isn't in the middle port.
  • Why can't my software connect to MAKCU?
    The COM number or the speed doesn't match, or another program has the port open.
  • How do I change MAKCU's baud rate?
    On v4 firmware, hold the left button for about a second. On v3, press it four times within two seconds. One flash is 115200 and four flashes is 4 Mbps.
  • Does restarting my PC reset MAKCU?
    No. It takes power from your main PC, so cold boot both PCs or replug the left cable.
Are we missing something?

Tell us what you came looking for and couldn't find, or what we got wrong, and we'll look into it. No account needed.

Did this help?

You don't need an account, this tells us what to write more of.