Skip to content
1 / 3
Aim DevicesBuilt by MAKCU

MAKCU

MAKCU aim device with 1000 Hz mouse passthrough and commands from your second PC. Arrives with v3 firmware.

$25.00
In stock
1

Only 5 left

To pay by card or anything other than crypto, open a ticket in our Discord. Card checkout on the site is coming in the next few months.

Free shipping
Tracked to your door
3-month warranty
Replaced if faulty
Tested
Checked before it ships
Build a bundle
0 of 4 parts
0% off3% off5% off10% off

Four parts chosen together take 10% off all four, and this one can start it.

Edit

What this is

MAKCU sits between your mouse and your two computers, and at $25 it's the cheapest part of a full setup. Your mouse plugs into it and it plugs into both computers, so your main PC only sees a normal mouse.

What it does

  • Three ports on the front edge.
    Hold MAKCU with the three ports pointing towards you. The left one goes to your main PC, the middle one to your second computer and the right one to your mouse.
  • Passes your mouse movement straight through, untouched.
  • Takes commands from your second computer.
    A third cable connects to your second computer. Your second computer opens a serial port to send MAKCU commands, which go to your main PC along with your mouse movement.
  • Arrives pre-flashed.
    It comes with v3 full passthrough firmware that works as it is, and for v4 Updating MAKCU to v4 walks you through the MAKCU Toolkit.

Good to know

  • 1000 Hz, and no faster.
    No firmware can change that, so for 8000 Hz you need FERRUM.
  • Software isn't included.
    Buy your software separately and run it on your second computer. We don't sell it, but Which DMA software to get lists our suggestions.
  • Keyboards work too.
    makcu.com says MAKCU supports keyboards as well as mice, and its current official firmware handles keyboards too.
  • Wireless works too.
    A wireless mouse or keyboard works through its own USB receiver, but Bluetooth doesn't go through it.
  • The aim device we recommend.
    It does the same job as FERRUM for a lot less, because FERRUM costs $160. FERRUM's one edge is 8000 Hz, and it doesn't have enough RAM to run ABCurves at that rate. ABCurves is a humanizer that makes the moves your software sends look like a real hand, splitting one big jump into lots of small curved moves. MAKCU vs FERRUM has the rest.
  • Tested before it ships.
    It comes with free tracked shipping and three months of warranty.
  • Full setup.
    MAKCU setup covers the wiring, the driver and the speed.

Paying

  • Crypto at checkout. If you've never sent crypto, How to pay with crypto shows you how. You can also pay by card through Stripe in a Discord ticket, for any amount, with a 10% fee.
  • Crypto payments are final. Unlike a card, a crypto payment can't be charged back, and crypto sent to the wrong address or network is gone for good. There are no returns on hardware and the warranty covers faults, so check our terms before you pay.
What arrives
  • 1x MAKCU board

  • 2 USB-A to USB-A cables, one for each computer

  • A 3D printed case, with buttons that press MAKCU's buttons

Our boxes come with everything you need. After you order, open a ticket in our Discord for support.

Before you buy
Not sure it's right for you?

We recommend MAKCU, and we don't recommend FERRUM. We stock FERRUM because some customers wouldn't buy from us without it. Read Why we recommend MAKCU for the reasons. If you have questions, ask on the forum so the answer helps other people too, or ask in our Discord.

Specifications

What it is
Type
Mouse passthrough and input relay
Recommended for
Everything. It is the aim device we recommend
Command set
MAKCU's own (API). Check your software supports MAKCU
Performance
Polling rate
1000 Hz
Input support
Mice
Supported
Keyboards
Supported, says makcu.com. It lists keyboard passthrough on v4 as coming soon, so ask in a ticket before you update
Input support, continued
Wireless
Yes, with its own USB receiver. Not Bluetooth
Game controllers
Supported, says makcu.com. It goes in the right port, like a mouse. Some controllers draw more power than it can give
Ports and setup
Left port
USB 1. To your main PC
Middle port
USB 2. To your second computer. This is the command port
Right port
USB 3. Your mouse or keyboard. Wired, or wireless with its own USB receiver
Software and firmware
Serial driver
CH343, installed on the second computer
Firmware updates
MAKCU Toolkit, free from MAKCU. How to update

Questions

Reviews

5.0
from 20 reviews
Write a review
zvsccyaNov 4, 2026

+rep 100T DMA with T2 FW and MAKCU Fuser Really good support and great product quality. Everything was well packaged

Helpful
.Oct 31, 2026

Rep phantom honestly I didn’t know whether to trust him or not at first but I really don’t regret it. Also excellent support thank you @phantom

Helpful